Ashly NXP3.04 Specs Amplifier Number of Channels 4 Voltage Gain Selectable at 26, 32, or 38 dB, or 1.4 V Damping Factor >250 (8 Ohms load <1 kHz) Filter Input High Pass Filter: 80 Hz 2nd order Distortion SMPTE (Typical): <0.5% THD-N (Typical): <0.5% (8 Ohms, 10 dB below rated power, 20 Hz to 20 kHz) Channel Separation -75 dB (dB from full output, 1 kHz) Signal-to-noise >114 dB (20 Hz to 20 kHz, un-weighted) Frequency Response 20 Hz to 20 kHz, ±0.05 dB Input Impedance 10 kOhms Balanced Input Euroblock 3.5 mm, 1/4" TRS and XLR combo jack Maximum Input Level +21 dBu Speaker Output Neutrik speakON Network Controllers Compatible with standard 100 MB Ethernet AUX Outputs Balanced Euroblock 3.5 mm Maximum Output Level +21 dBu (Aux output) Standby Mode Euroblock 3.5 mm, close contact to GND for standby mode Preset Euroblock 3.5 mm, close contact to GND for preset 1-4 recall Data Data Connection: Euroblock 3.5 mm - GND, 18 V, in, out Outputs Fault Condition Logic Outputs: 4 / 3.5 mm Euroblock Level Control Remote DC Level Control: Euroblock 3.5mm - GND, CV, V+ per input Audio Control Module Network Audio via CobraNet digital interface (pre-installed) Attenuation Per Channel: Front panel, software, offset link group, and remote Fully off = Mute Front Panel LED Indicators White LED: Power Switch: On, off, flashing (standby mode) Red LED: Protect: On (fault condition or shut down), Off Clip / Mute (Per Channel): Clip @ 1 dB below full output / mute Blue LED: Sleep Mode: On (when the amplifier is asleep from audio inactivity) Yellow LED: Disable: On (when the power switch & front panel attenuators are disabled) Temperature (Per Channel): On dim at 90% maximum operating temperature, full bright + protect at 100% Green LED: Com: On, for Ethernet data or device ID Signal (Per Channel): -18 dBu, below rated output Bridge (Per Channel): On, off Current (Per Channel): Proportional to output Protection Circuits Inrush current limitation, temperature monitoring, output over-power protection, and mains fuses Protea DSP Input Source Protea DSP Options: Analog, auto (net, AES3, analog) Limiter Brick Wall Limiter Threshold: -20 to 20 dBu Ratio: Infinite Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB Compressor Threshold: -20 to +20 dBu Ratio: 1.2:1 to infinite Attack: 0.2 to 50 ms Release 5 to 1000 ms/dB Detector: Peak/Average Attenuation Bus: 2 available Metering: In, Out, Attenuation, Graphical Controls Autoleveler Controls Target Level: -40 to +20 dBu Action: Gentle, Normal, Aggressive, User-Defined Maximum Gain: 0 to +22 dB Metering: Input, Gain, Attenuation Ratio: 1.2:1 to 10:1 Threshold Below Target: -30 to 0 dB Gain Increase/Decrease Rate: 5 to 1000 ms/dB Hold Time: 0 to 6 sec Ambient Noise Compensation Output only Max Gain: -20 to +20 dB Min/Base Gain: -40 to +20 dB Gain Change Rate: 0.2 to 20 s/dB Link Group: 16 available ANC Input Channel: 1 to 2 or 1 to 4 Noise Threshold -40 to +20 dBu Program/Ambient Gain Ratio; 0.3:1 to 3:1 Metering: Input level, Attenuation, Average noise Ducking High/Low Priority, Trigger, Filibuster, Ducked Program Trigger Threshold: -80 to +20 dBu Ducking Release: 5 to 1000 ms/dB Ducking Depth: 0 to -30 dB, -8 Enable ducking at matrix mixer Metering input Gate Threshold: -80 to +20 dBu Range: Off, 100 to 0 dB Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB Metering: Key signal, gate LED, graphical Advanced Gate Controls Key engage enable Key Frequency: 20 Hz to 20 kHz Key Bandwidth: 0.016 to 3.995 octave Gain Gain (with / without VCA): -50 to 12 dB, off, polarity invert Digital VCA Groups: 4 available Remote RD8C Gain: Enable per channel, 0 dB to -8 WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute EQ Type For FIR Filter Output only, 48 kHz only, 2-384 taps File Type: .csv, .fir For 31-Band Filter Type: Constant Q or proportional Bandwidth: 0.499 octave to 0.25 octave For Parametric 2,4,6, or 10 Band Frequency: 20 to 20 kHz Level: -30 to 15 dB Q Value: 0.016 to 3.995 octave For Hi / Low Shelf 6 / 12 dB/octave Frequency: 20 Hz to 20 kHz Level: -15 to 15 dB For All Pass Frequency: 20 Hz to 20 kHz For Variable Q HP / LP Frequency: 20 Hz to 20 kHz Q Value: 3.047 to 0.267 For Notch / Bandpass Frequency: 20 Hz to 20 kHz Q Value: 92.436 to 0.267 Feedback 48 kHz Sampling Rate 12 x filters In/Out per filter Lock (per filter) and global lock Filter Modes: Float, restricted, manual Filter Type: Notch, parametric Filter Frequency Range: 20 Hz to 20 kHz Notch Filter: -8 Parametric Filter: 15 to -30 dB Filter Bandwidth 0.016 to 3.995 Octave Detector Sensitivity: 5 levels Float Time 5 minutes to 24 hours Crossover 2 Way, 3 Way, 4 Way Crossover & High Pass / Low Pass Filters Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave Frequency: Off, 20 Hz to 20 kHz Delay At 48 kHz Sampling Rate (Input Time, Distance & Temperature): Speaker Delay: 0 to 21 ms Delay: 0 to 682 ms At 96 kHz Sampling Rate (Input Time, Distance & Temperature): Speaker Delay: 0 to 10.6 ms Delay: 0 to 341 ms Audio Metering Range: -60 to 20 dBu Increments: 1 dB Peak Hold Indicator Signal Generator Pink Noise, White Noise, Sine Wave Signal Level: Off, -50 to 20 dBu Sine Wave Frequency: 20 Hz to 12 kHz Mixer Matrix Mixer: Gain (0.5 dB Increments): Off, -50 to 12 dB Mute: Per channel Auto-Mixer Enabled: Per channel Global Auto-mixer Response: 0.01 to 2 sec Enable Ducking at Mixer Ducking LED: Per channel if enabled Metering: Level, auto-mixer level Processor Input A/D, Output D/A: 24 bit DSP Processors: 32-bit floating point Sample Rates: 48 kHz, 96 kHz Propagation Delay @ 48 kHz: 1.42 ms Propagation Delay @ 96 kHz: 0.71 ms Power Requirements Nominal Automatic Sensing SMPS: 120 VAC @ 60 Hz 240 VAC @ 50 Hz Operating Range 70 to 135 VAC @ 60 Hz 140 to 270 VAC @ 50 Hz Power Minimum Power-Up: 85 VAC @ 60 Hz 170 VAC @ 50 Hz Power Cable 32 A powerCON Maximum Output Power Per Channel, Low-Z Output, All Channels Driven: 2 Ohms: 3,000 W 4 Ohms: 2,000 W 8 Ohms: 1,250 W Low Impedance Bridge Mode (All Channels Driven): 4 Ohms: 6,000 W 8 Ohms: 4,000 W 70 V, 100 V Output (All Channels Driven): 70 V (Per Channel): 2,450 W 100 V (Per Channel): 1,250 W Power Draw Sleep Mode: <1 W Standby Mode: 70 W Idle (No Signal): 100 W Maximum Current Draw All Channels Driven, Typical Input (1/8 Max Power @ 2 Ohms): 29.5 A for 120 VAC 14.75 A for 240 VAC Current Draw For 120 VAC Sleep Mode: 0.1 A Standby Mode: 1.3 A Idle (No Signal): 1.85 A For 240 VAC Sleep Mode: 0.05 A Standby Mode: 0.65 A Idle (No Signal): 0.925 A Dissipation Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 238 BTU/hr Idle (No signal): 340 BTU/hr Typical (1/8 Max Power @ 2 Ohms): 2,720 BTU/hr General Cooling Continuously variable temperature controlled axial fans Environmental Non-condensing 32 to 113°F (0 to 45°C) Dimensions 19.00 x 3.50 x 16.84" (483 x 89 x 428 mm) Weight 28.7 lb (13 kg)